Lead flashing around a brick chimney, our lead work service for homes and businesses

Local, Reliable, Professional

Lead Work in Preston

Sheet lead that keeps water out of the joints in your roof, from simple flashings to dormers and roof features.

  • Free, no obligation quotes
  • Experienced, fully insured team
  • High quality, long lasting results
  • Covering Preston and surrounding areas

Get a Free Roofing Quote

Tell us what you need and we'll get back to you as soon as we can.

We only use these details to reply to your enquiry and prepare your quote. We do not share them for marketing and we keep them for up to 12 months. Read our privacy notice.

  • Free Quotes No obligation

  • Fully Insured For your peace of mind

  • Local Team Preston & surrounding areas

  • Trusted Locally Built on recommendations

Lead Work

Where the roof stops, the lead takes over

Tiles and slates shed water well while they are lapped over each other. The weak points come where that pattern stops, at a wall, a chimney, a valley or a pipe through the roof. Those joints need a material that can be shaped to fit and still keep rain out, and for generations that has been sheet lead. Historic England describes flashings as often the most vulnerable part of a roof, so they deserve careful work.

Lead has to be allowed to move. It expands in warm sun and shrinks back in the cold, and a piece that is too long or fixed too tightly can buckle and crack. Trade guidance limits flashings to lengths of 1.5 metres, with 100mm laps at the joints and the top edge turned at least 25mm into the wall. When lead fails, the cause is usually the way it was sized or fixed rather than the metal itself.

We carry out a wide range of work in sheet lead on homes, commercial premises and industrial roofs around Preston. That runs from simple flashings at valleys, abutments and roof penetrations up to the more complex detailing found on dormers and roof features. Sometimes one crack can be put right. Sometimes a whole length has had its day. We will tell you which. Repairs are agreed in advance and quoted on their own.

  • Flashings at walls and abutments
  • Lead flashings at valleys
  • Flashings around roof penetrations
  • Chimney stack flashings
  • Complex lead work on dormers
  • Roof features in sheet lead
  • Repairs to split or lifted lead
Lead flashing around a brick chimney on a tiled roof, a closer view from our lead work service

When to Call Us

Telltale marks of lead work on its way out

  • Flashing lifting away from the wall

    Wind gets behind a flashing once its wedges or clips work loose, and the pointing along the top joint starts to crack away. Rain can then run straight down behind the lead, so the leak may show some distance from the joint.

  • Raised ridges and fine cracks

    A raised ridge in a lead valley or gutter shows the sheet has been unable to move. Cracks usually follow. Water can seep through for a long time before a stain shows indoors, and the timber underneath may already be rotting when it does.

  • Moss draining onto the metal

    Rain that runs through moss and lichen turns mildly acidic, and over time it eats into lead. Valleys and flashings sitting below heavy growth are the ones to have checked, before the metal thins enough to leak.

How We Work

Putting failed lead work right

  1. Rule out the roof above

    A stain near a chimney may begin at a slipped tile higher up, so that gets ruled out first. Then we judge the lead itself, the joint it sits in and the roofing around it.

  2. Patch it or renew it

    Mostly sound lead with a minor split is often repairable. Lead that has failed along its length is usually better renewed. You get our view on which applies, and the work is quoted separately.

  3. Size the lead, then dress it

    The lead is cut to sizes that suit its position, then dressed to the shape of the roof. Separate lengths are lapped rather than joined rigidly, so each piece can move.

  4. Wedge, clip and oil

    Flashings are turned into the mortar joint, wedged and sealed, with free edges clipped against wind. Patination oil is normally applied to new lead to help stop white staining on the roof below.

Our Work

Examples of Our Roofing Work

Photos from roofs we have worked on across Lancashire.

  • Lead lined valley running down a roof beside the scaffold, a photo from our lead work service
  • Old lead valley lifted during a roof repair, shown as part of our lead work service
  • Worn out roof valley exposed during repair work, the kind of lead work we take on
  • Roof valley being stripped and relined with new membrane, part of how we approach lead work

See the full gallery

Questions

Lead Work Questions

Which code of lead does my roof need?

The code tells you the thickness. Code 4 is 1.80mm and Code 5 is 2.24mm. One manufacturer's sizing guide lists Code 4 for soakers, flashings, pitched valleys and dormers, with Code 5 upwards for flat roofing and box gutters. Position and exposure both affect the choice, so you will know which code we propose, and why, before any lead is cut.

Can a cracked lead flashing be repaired without replacing it?

A small piece of new lead, set into the joint above the crack and lapped at least 100mm past it on each side, will often do the job. Repair tape only buys a little time. If the flashing has cracked in several places, or was fitted in lengths that are too long, renewing it is usually the better answer.

Why has white staining appeared below my new lead?

New lead reacts with rainwater and forms a white carbonate, which can wash onto the tiles, brick or stone below. Patination oil helps to prevent this and is normally applied to newly fitted lead. In time the surface weathers to a dull grey that protects the metal. White streaks seeping from under old laps can point to something else, corrosion caused by condensation underneath.

Are there alternatives to lead, and can I use them?

The trade also uses synthetic flashing products and fibreglass valley linings. They can suit some modern roofs, but conservation guidance is cautious about them on older buildings. On a listed building, swapping lead for another material is likely to need listed building consent, and changing the lead code may need it too. If your home is listed or in a conservation area, ask the council's conservation officer first.

Related Services

More Ways We Can Help

Brick house with a dark tiled gable roof, ask us for a free quote for lead work

Need Help With Lead Work?

Get in touch today for a free, no obligation quote.